Beware the words "just one more." James "Slim" Janssen can tell you why. Not so long ago, the blue F-250 on these pages was glimmering white. During a long weekend in the desert, yours truly was en route from another corner of the Mojave, planning to meet Slim and the rest of the Mojave Mafia for a few hours of photo shoot fun. James and crew had spent most of the afternoon playing in the whoops and turns near the Slash X Café in Stoddard Valley. It was time to give the truck a wipe-down. Before parking, the proud owner cranked the wheel and hit the throttle in the name of "just one more" powerslide. Mid-slide, the outside rear tire blew off its bead, hooking the wheel in terra firma, and sending the truck rubber-side up. Oops.
With a wrinkled cab and no shortage of mangled fiberglass, the repairs seemed daunting. Thanks to Slim's "original" approach to building his truck, it went back together with relative ease. A few months later, the newly-blue Ford was ready for another shoot. When the date arrived, James kept his truck parked pending the photographer's arrival.
That's the story of the photo shoot. Now let's concentrate on the truck's build.
Keith Sato built the front bumper that leads the way. Three Sol Tek HID lights make after-
James bought the truck already built, and the original build used bolt-on roll cage and suspension construction. Even though he ended up redoing most of the build, new 'cage and suspension components were still bolted to the frame rather than welded directly on. Bolt-on construction takes more time during the initial build. Instead of welding directly to the frame, landing plates are made to bolt on. This means spending time making the landing plates, and spending time drilling holes in the frame to mount them. Once the plates are bolted in place, rollcage tubing can "land" on the plates. This method also applies to leaf spring hangers, bump stop mounts, and radius arm brackets.
The bolt-on method has a couple of advantages. First, roll cage sections and suspension components can be unbolted during maintenance and repair. Second, the bolts allow a little bit of "give" between the 'cage and suspension components and the frame. This give helps avoid stress cracks.
A set of Trailer Products bedsides partially camouflage the suspension and structural upgr
The front suspension is classic and simple. Kingpin-style I-beams were slightly extended and then plated in for maximum strength. The rear-steer knuckles were retained, along with the OEM-configuration steering linkage. Tony Sato built James a set of billet front hubs which are lighter and stronger than the '73 pieces. The early '90s flavor comes from the coil bucket-mounted springs and the dual smooth-body Fox 2.0 shocks. A Fox bumpstop on each side updates the performance during hard hits.
Slim's truck is based on a '73 F-250 frame. Instead of the '73 cab, an '85 unit was grafted on. The front fiberglass and grille are '87-to-'91-style and bring on thoughts of the 1990s, a decade still considered by many as desert racing's finest years.
The big 400 breathes through a UNI filter, and is cooled by an all-aluminum PWR radiator.
Out back, the bolt-on leaf spring hangers and matching bolt-on shackle brackets are home to a pair of Deaver leaf packs that mount to the top of a Currie-built Ford 9-inch rearend. James wanted to use the same old-school shock setup that the front end had, but found it impossible to achieve the same control using smooth-body shocks. Shock tuning on both ends comes courtesy of Keith Sato, who is Tony's brother and a fellow Mojave Mafia member.
Under the dropped-center fiberglass hood, you'll find a mildly-built Ford 400M V-8. A Clay Smith cam, roller rockers, and a 750 cfm double-pumper carburetor help produce about 400 ponies. Behind the 400, a Ford C6 transmission translates crank rpm into driveshaft rpm. The C6 was built by Roy's Transmission in Fullerton, California, who fitted the heavy-duty automatic with a fixed-yoke output. Lucas Oil products lubricate the entire truck.
-
A PWR tranny cooler controls the temperature inside the C6. Note the through-bolt plates t
-
The original '73 steering linkage still runs behind the kingpin I-beams, albeit with some
-
Did we mention everything bolts on? Note the slick little protector for the brake line's f
Dual Fox 2.0 smooth body shocks and a bucket-captured coil spring are old-school, but were
Anything else? Definitely. There's no shortage of spare parts on this truck, each with its own slick James-built mount. If the starter dies, James has a spare for that. If the alternator lets loose, James has a spare for that, too. The same goes for the steering tie rods and drive shaft. Tools, along with recovery gear, are also close at hand. "I was on a 7s racing team," James informed. "We ran a Toyota in Best in the Desert and I learned a lot from that experience. When it was time to build my Ford, I already knew what spares I should carry and how I wanted to mount them."
With the close-ups snapped, it was time for Slim and the F-250 to face off with the desert. James hit the whoops, slammed The Wall, and powerslid Anderson dry lake. Thanks to a set of newly-fitted Champion beadlocks, the tires stayed firmly mounted and the rubber side stayed down.
Even the best-tuned smooth-body shocks can't match the tune-ability and position-sensitive
It was good to see Original Slim and his truck back in action. Rollover repairs often take multiple months, if not years, to complete. Thanks to savvy building techniques and equally-adept friends, the truck was back in blue in a hurry. Even though repairs can be performed, it's always easier to avoid a crash in the first place. What's the best way to do that? Resist the urge to say, "Just one more."
Specs
Vehicle:
'73 Ford F-250
Owner/Hometown:
James Janssen / Lake Elsinore, California
Engine:
Ford 400M with Clay Smith cam, roller rockers, UNI air filter, MSD distributor
Induction:
750 cfm double-pumper carburetor
Cooling:
PWR radiator, PWR transmission cooler
Transmission:
Ford C-6 with fixed output yoke built by Roy's Transmissions
Front Suspension:
Kingpin I-beams extended and plated, Fox smooth-body shocks, Fox bumpstops, 16 inches of travel
Rear Suspension:
Deaver leaf packs with spring-over mount, Fox 2.5 bypass shocks, Fox bump stops, 16 inches of travel
Rear Axle:
Currie-built Ford 9-inch with Wilwood disc brakes
Tires:
35-inch BF Goodrich Baja T/As
Wheels:
American Racing Outlaw II fitted with Champion beadlocks
Interior:
Mastercraft seats, Crow harnesses, Lowrance GPS, Autometer gauges, dash built by James, headliner, seat covers, and door panels by Yvonne Janssen, Kreger Fab tilting steering column, Kenwood race radio
-
Mastercraft seats and Crow harnesses cradle and secure driver and co-driver. James's wife
-
First aid is within close reach, as is a fire extinguisher and the main electrical shutoff
-
James built this dash, which is home to Autometer gauges and a Kreger Fabrication tilting
-
A set of Champion beadlocks holds the 35-inch BF Goodrich Baja T/As in place during hard c
-
"The Wall" in Lucerne Valley is a favorite jump for testing metal and mettle. The short, a
-
-
Everything In Its Place
After the main parts of a truck build (suspension, drivetrain, a
-
......one of the biggest challenges is creating places to store spare parts and tools. Flu
-
.....also need a home. James created hold-downs, brackets, and mounts for everything he ne
-
.....There's nothing more annoying than reaching for something only to realize.....
-
....it bounced off the truck into the desert several miles ago.